Name: DG611DY
Brand: Vishay Siliconix
SKU: DG611DY
Availability: InStock

new-10%

DG611DY

Manufacturer part number:DG611DY

Manufacturer:Vishay Siliconix

Description:35ns, 25ns SPST - NC 45Ohm Analog Switches BREAK-BEFORE-MAKE 16 Pins 250pA 16-SOIC (0.154, 3.90mm Width)

Case Package:SOT-23

Datasheet:DG611DY Datasheet PDF

RoHs Status:non-compliant

Parameter Name	Value
Type	Parameter
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-SOIC (0.154, 3.90mm Width)
Number of Pins	16
Weight	665.986997mg
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2015
JESD-609 Code	e0
Pbfree Code	no
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	45Ohm
Terminal Finish	Tin/Lead (Sn/Pb)
Subcategory	Multiplexer or Switches
Max Power Dissipation	600mW
Terminal Form	GULL WING
Number of Functions	4
Terminal Pitch	1.27mm
Reach Compliance Code	unknown
Output	SEPARATE OUTPUT
Pin Count	16
Qualification Status	Not Qualified
Power Supplies	515-3V
Max Supply Voltage	18V
Min Supply Voltage	10V
Operating Supply Current	5nA
Nominal Supply Current	5nA
Power Dissipation	600mW
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	35 ns
Number of Inputs	4
Voltage - Supply, Single/Dual (±)	10V~18V ±10V~15V
Supply Type	Dual, Single
Bandwidth	500MHz
Turn-Off Delay Time	25 ns
Max Dual Supply Voltage	15V
On-State Resistance (Max)	45Ohm
Min Dual Supply Voltage	10V
Multiplexer/Demultiplexer Circuit	1:1
Current - Leakage (IS(off)) (Max)	250pA
Channel Capacitance (CS(off), CD(off))	3pF 2pF
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	35ns, 25ns
Charge Injection	4pC
Channel-to-Channel Matching (ΔRon)	2 Ω
Crosstalk	-87dB @ 5MHz
Switching	BREAK-BEFORE-MAKE
Drain to Source Resistance	45Ohm
Normal Position	NC
Height	1.55mm
Length	10mm
Width	4mm
RoHS Status	Non-RoHS Compliant
Lead Free	Contains Lead

DG611DY Product Details

DG611DY Overview

Packed in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Temperatures around -40°C~85°C TA are extended for operation. The total number of terminations is 16. As part of its design, the 16 series is equipped with this electronic component. Unlike digital switches, these are based on SPST - NC switching circuits. The internal resistance of this digital multiplexer is 45Ohm. For functions related to 16 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 18V. The analog switch ic is of the Dual, Single supply type and is cost-effective. A low voltage of 10V should be applied to the electronic component. It would be sufficient to run this analogue multiplexer with 5nA current. It may damage the digital multiplexer if the voltage is higher than 1μA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 15V. A dual power supply should have at least 10V voltage attached. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. Operating 4 inputs is required. The transfer of data can be performed over 500MHz bandwidths. This electronic component presents a Drain to Source resistance of 45Ohm.