Name: DG2722DN-T1-E4
Brand: Vishay Siliconix
SKU: DG2722DN-T1-E4
Availability: InStock

new-10%

DG2722DN-T1-E4

Manufacturer part number:DG2722DN-T1-E4

Manufacturer:Vishay Siliconix

Description:30ns, 25ns DPDT 8Ohm QUAD Analog Switches BREAK-BEFORE-MAKE DG2722 10 Pins 100nA 3V 10-UFQFN

Case Package:SOT-23

Datasheet:DG2722DN-T1-E4 Datasheet PDF

RoHs Status:non-compliant

Parameter Name	Value
Type	Parameter
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	10-UFQFN
Number of Pins	10
Weight	7.002332mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2016
JESD-609 Code	e4
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	10
Resistance	8Ohm
Terminal Finish	Nickel/Palladium/Gold (Ni/Pd/Au)
Subcategory	Multiplexer or Switches
Max Power Dissipation	208mW
Technology	CMOS
Terminal Position	QUAD
Peak Reflow Temperature (Cel)	260
Number of Functions	2
Supply Voltage	3V
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	DG2722
Pin Count	10
Number of Outputs	4
Operating Supply Voltage	3V
Power Supplies	3V
Number of Channels	1
Number of Circuits	2
Max Supply Voltage	4.3V
Min Supply Voltage	2.6V
Operating Supply Current	2μA
Power Dissipation	208mW
Turn On Delay Time	30 ns
Data Rate	480 Mbps
Supply Type	Single
Bandwidth	900MHz
Turn-Off Delay Time	25 ns
On-State Resistance (Max)	8Ohm
Multiplexer/Demultiplexer Circuit	2:2
Off-state Isolation-Nom	30 dB
Current - Leakage (IS(off)) (Max)	100nA
Channel Capacitance (CS(off), CD(off))	2.2pF
On-state Resistance Match-Nom	0.8Ohm
Switch Circuit	DPDT
Switch Time (Ton, Toff) (Max)	30ns, 25ns
Charge Injection	0.5pC
Channel-to-Channel Matching (ΔRon)	800m Ω
Crosstalk	-45dB @ 240MHz
Switching	BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+)	2.6V~4.3V
Height	550μm
Length	1.8mm
Width	1.4mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant

DG2722DN-T1-E4 Product Details

DG2722DN-T1-E4 Overview

Shipping overseas is convenient with the electronic component packed in 10-UFQFN. High reliability is provided by advanced packaging method Tape & Reel (TR). In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have a ratio of 2:2. Temperatures around -40°C~85°C TA are extended for operation. Total terminations are 10. High-quality output is provided by the electronic component's 1 channels. If the voltage supply is 3V volts, the electrical component should be turned on and run. The electronic part body is injected with 10 pins. A DPDT switching circuit is used to build these analog multiplexers. There are 2 circuits in this multiplexer. Try searching with DG2722 if you're looking for variants. There is 8Ohm internal resistance in this digital multiplexer. For functions related to 10 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. A voltage higher than 4.3V should not normally be supplied to the switches. Analogue multiplexers of the Single supply type that are cost-effective. 2.6V should be the lowest voltage fed to the electronic component. For this multiplexer to operate, 2μA current would be sufficient. This analog switch requires a voltage of 2.6V~4.3V to drain from a single voltage supply. 3V operating voltages are supported by the electronic component. A 900MHz-bandwidth can be used for data transfer. The analogue multiplexer has 4 outputs.