Name: DG442DY-T1-E3
Brand: Vishay Siliconix
SKU: DG442DY-T1-E3
Price: 2.73000 USD
Availability: InStock

new-10%

DG442DY-T1-E3

Manufacturer part number:DG442DY-T1-E3

Manufacturer:Vishay Siliconix

Description:250ns, 210ns SPST - NO 85Ohm Analog Switches BREAK-BEFORE-MAKE DG442 16 Pins 500pA 15V 16-SOIC (0.154, 3.90mm Width)

Case Package:SOT-23

Datasheet:DG442DY-T1-E3 Datasheet PDF

RoHs Status:non-compliant

Parameter Name	Value
Type	Parameter
Factory Lead Time	13 Weeks
Contact Plating	Tin
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-SOIC (0.154, 3.90mm Width)
Number of Pins	16
Weight	665.986997mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2013
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	85Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	900mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	15V
Terminal Pitch	1.27mm
[email protected] Reflow Temperature-Max (s)	30
Base Part Number	DG442
Pin Count	16
Polarity	Non-Inverting
Number of Channels	1
Max Supply Voltage	36V
Min Supply Voltage	13V
Operating Supply Current	15μA
Nominal Supply Current	15μA
Power Dissipation	900mW
Max Supply Current	100μA
Throw Configuration	SPST
Turn On Delay Time	250 ns
Number of Inputs	4
Voltage - Supply, Single/Dual (±)	12V ±15V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	120 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	85Ohm
Min Dual Supply Voltage	7V
High Level Output Current	30mA
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	60 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	4pF 4pF
On-state Resistance Match-Nom	4Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	250ns, 210ns
Charge Injection	-1pC
Channel-to-Channel Matching (ΔRon)	4 Ω (Max)
Crosstalk	-100dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-off Time-Max	210ns
Drain to Source Resistance	50Ohm
Normal Position	NO
Height	1.55mm
Length	10mm
Width	4mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

DG442DY-T1-E3 Product Details

DG442DY-T1-E3 Overview

Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). It is mounted in the position Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. The operating temperature is extended to around -40°C~85°C TA. A total of 16 terminations have been recorded. Due to its 1 channels, the electrical component produces high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. Into the electrical component body are injected 16 pins. Circuits based on SPST - NO switching are used to construct these analog switch ics. Try searching with DG442 if you're looking for variants. A 85Ohm internal resistance characterizes this multiplexer. Please refer to the datasheets for 16 pins functions. There is Multiplexer or Switches analog multiplexer like this in the world. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. Dual, Single supply type digital switch with a low cost. 13V is the lowest voltage the electrical component should receive. An operating current of 15μA would be sufficient for this switch device. Putting voltage greater than 100μA on the multiplexer may cause damage. There is no problem with using dual supply voltage, but it should not exceed 22V. The voltage should be at least 7V if you are using dual power supplies. Operating 4 inputs is required. There is 50Ohm resistance between Drain and Source for this electronic part.