Name: DG211BDJ-E3
Brand: Vishay Siliconix
SKU: DG211BDJ-E3
Price: 2.46000 USD
Availability: InStock

new-10%

DG211BDJ-E3

Manufacturer part number:DG211BDJ-E3

Manufacturer:Vishay Siliconix

Description:300ns, 200ns SPST - NC 85Ohm Analog Switches BREAK-BEFORE-MAKE DG211 16 Pins 500pA 15V 16-DIP (0.300, 7.62mm)

Case Package:SOT-23

Datasheet:DG211BDJ-E3 Datasheet PDF

RoHs Status:non-compliant

Parameter Name	Value
Type	Parameter
Factory Lead Time	12 Weeks
Contact Plating	Tin
Mount	Through Hole
Mounting Type	Through Hole
Package / Case	16-DIP (0.300, 7.62mm)
Number of Pins	16
Weight	1.627801g
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2005
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	160Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	470mW
Technology	CMOS
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	15V
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG211
Pin Count	16
Polarity	Non-Inverting
Power Supplies	512/+-15V
Number of Channels	1
Max Supply Voltage	25V
Min Supply Voltage	4.5V
Operating Supply Current	10μA
Nominal Supply Current	50μA
Power Dissipation	470mW
Max Supply Current	10μA
Throw Configuration	SPST
Turn On Delay Time	300 ns
Number of Inputs	4
Voltage - Supply, Single/Dual (±)	4.5V~25V ±4.5V~22V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	200 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	85Ohm
Min Dual Supply Voltage	4.5V
High Level Output Current	100mA
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	90 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	5pF 5pF
On-state Resistance Match-Nom	2Ohm
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	300ns, 200ns
Charge Injection	1pC
Channel-to-Channel Matching (ΔRon)	2 Ω
Crosstalk	-95dB @ 100kHz
Switching	BREAK-BEFORE-MAKE
Drain to Source Resistance	50Ohm
Normal Position	NC
Height	3.81mm
Length	21.33mm
Width	7.11mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

DG211BDJ-E3 Product Details

DG211BDJ-E3 Overview

This electronic part is conveniently packaged in 16-DIP (0.300, 7.62mm), making it easy to ship abroad. This high-reliability packaging method uses advanced packaging methods Tube. A switch device like this is mounted in Through Hole. 1:1 is the ratio of multiplexer to demultiplexer circuits. An extended operating temperature of -40°C~85°C TA degrees Celsius. In total, there have been 16 terminations. A 1 channel electronic part produces high-quality output. A 15V voltage supply should turn on and run the electronic component. An injection of 16 pins is performed into the body of the electrical component. Unlike digital switches, these are based on SPST - NC switching circuits. Try searching for DG211 variants of the analog switch ic. Analog switches have 160Ohm internal resistance. To find out what the 16 pins do, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. Users should never supply a voltage higher than 25V to a switch device. Analog switch ics with Dual, Single supply type are cost-effective. There should be 4.5V voltage fed to the electrical part below 4.5V. It would be sufficient to run this analogue multiplexer with 10μA current. The switch multiplexer may be damaged if it is exposed to voltage greater than 10μA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. The voltage should be at least 4.5V if you are using dual power supplies. In order to operate the 4 inputs, there are several steps to follow. Resistivity from Drain to Source is 50Ohm for this electronic part.